UBI EasyCoder 201 II Spécifications Page 141
- Page / 270
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7— IPL Command Reference
IPL Programmer’s Reference Manual 125
Label Stock Type, Select
Purpose: Selects the type of label stock.
Syntax: <SI>Tn
where n specifies the type of stock.
Printers:
Printer Default Values for n Notes
All n = 1
0 = Continuous label stock (no
breaks between labels)
1 = Label stock with gaps between
labels
2 = Label stock with marks between
labels (on back of label stock)
All printers support this
command the same way.
Notes: To make this command effective, reset the printer or turn the power off
and on again after issuing the command.
Label Width, Set
Purpose: Sets the label width to n in dot increments.
Syntax: <SI>Wn
where n is a number between the minimum and maximum number of
dots for your printer. Calculations for all printers (except the 4440 printer)
use a 5 mil dot.
Printers:
Printer Default Values for n Notes
4400
n = 896
n = 672
(6.5 mil printhead)
50 to 896
or
50 to 672
This command is effective
upon execution.
44X0
4420: n = 896
4440: n = 1792
4420: 50 to 896
4440: 100 to 1792
This command is effective
upon execution. For the
4440 printer, n must be
calculated using 2.5 mil
dot.
7421 n = 832 50 to 832
This command is effective
upon execution.
Notes: (44X0 only) When you print narrower labels, set this command to reduce
torque. You may need to experiment with this command until your labels
print properly. In high humidity environments, you may also want to use
the Takeup Motor Torque, Increase command.
- IPL (Intermec Printer 1
- Language) 1
- Programmer's 1
- Reference Manual 1
- Document Change Record 3
- Contents 10
- Before You Begin 13
- Safety Icons 14
- Global Services and Support 14
- Related Documents 15
- Introduction to IPL Commands 17
- What Is IPL? 18
- What Are IPL Commands? 18
- <STX>E2;F2<ETX> 20
- <STX> 20
- Example 1 23
- Example 2 23
- What to Read Next 24
- Downloading Fonts to the 25
- Printer 25
- Licensing Your Fonts 31
- Installing Code Page Tables 33
- Downloading Bitmap Fonts 34
- Downloading Outline Fonts 34
- Designing Bar Code Labels 37
- Introduction to Formats 38
- THIS IS THE SAMPLE LABEL 39
- Sample Label Command Strings 42
- Defining Label Design Fields 43
- Line and Box Fields 44
- Lines and Boxes Format 45
- Graphic Fields 46
- Editing Existing Fields 49
- Deleting Fields 50
- Positioning Fields 50
- Rotating Fields 51
- Scaling Fields 52
- Magnifying Bar Code Fields 53
- DUPLEX ANGLE CONNECTOR 54
- Graphic for Example 55
- Format for Example 55
- Data for Example 56
- Troubleshooting 59
- Troubleshooting Checklist 60
- Parameter Errors 61
- Image Overrun Errors 61
- Chapter 4— Troubleshooting 64
- Advanced Printer 65
- Programming 65
- Increasing Throughput 67
- Image Band Example 69
- Reimaging Modified Fields 71
- Using Emulation Mode 72
- Finding IPL Commands in This 79
- Commands Listed by Name 80
- Commands Listed by Syntax 84
- Commands Listed by Task 88
- Box Field Editing Commands 89
- Format Editing Commands 89
- Line Field Editing Commands 90
- Page Editing Commands 91
- Programming Commands 91
- UDC Field Editing Commands 91
- UDC Editing Commands 91
- Print Mode Commands 92
- IPL Command Reference 95
- Immediate Commands 102
- Status Dump 104
- Status Enquiry 105
- Print Commands 106
- Advanced Mode, Select 107
- Alphanumeric Field Separator 108
- Batch Count, Set 109
- Clear All Data 109
- Command Terminator 1 109
- Command Terminator 2 110
- Direct Graphics Mode, Select 112
- Emulation Mode, Enter 113
- Field, Select 113
- Field Decrement, Set 114
- Field Increment, Set 115
- Font, Transmit 116
- Form Feed 117
- Format, Select 117
- Format, Select (continued) 118
- Printers: 118
- Format, Transmit 119
- <ESC>N 120
- Memory Usage, Transmit 121
- Numeric Field Separator 122
- Options Selected, Transmit 123
- Page, Select 124
- Page, Transmit 124
- Program Mode, Enter 125
- Program Number, Transmit 126
- Quantity Count, Set 126
- Storage Area Usage, Transmit 127
- Test and Service Mode, Enter 127
- Warm Boot 128
- Configuration Commands 129
- Amount of Storage, Define 130
- Auto-Transmit 1, Enable 131
- Auto-Transmit 2, Enable 131
- Auto-Transmit 3, Enable 131
- Syntax: <SI>An 133
- Printers: 133
- Cutter, Enable or Disable 134
- Dark Adjust, Set 134
- Syntax: <SI>Cn 135
- Intercharacter Delay, Set 138
- Label Rest Point, Adjust 139
- Label Retract Distance, Set 140
- Label Stock Type, Select 141
- Label Width, Set 141
- Maximum Label Length, Set 142
- Media Sensitivity, Select 143
- Message Delay, Set 144
- Number of Image Bands, Set 145
- Pin 11/20 Protocol, Set 146
- Postamble, Set 147
- Preamble, Set 147
- Print Speed, Set 148
- Printer Language, Select 149
- Printhead Pressure, Set 152
- Ribbon Save Zones, Set 153
- Top of Form, Set 155
- Program Mode Commands 156
- Bar Code, Select Type 157
- Code 39 158
- Code 93 158
- Interleaved 2 of 5 159
- Code 2 of 5 159
- Codabar 159
- Code 11 160
- Code 128 160
- UPC/EAN 162
- HIBC Code 39 163
- Code 16K 163
- Code 49 164
- POSTNET 164
- Code One 167
- MaxiCode 170
- JIS-ITF 172
- HIBC Code 128 173
- QR Code 175
- MicroPDF417 176
- Syntax: yn 178
- Printers: 178
- Box Field, Create or Edit 182
- Syntax: rn 184
- Command Tables, Load 187
- Current Edit Session, Save 188
- Field, Delete 188
- Field Data, Define Source 189
- Field Direction, Define 191
- Field Origin, Define 191
- Font Character Width, Define 192
- Font Type, Select 194
- Format, Create or Edit 196
- Within a Page, Define 198
- Graphic, Select 200
- Graphic or UDC, Define 200
- Syntax: hn 201
- Interpretive Field, Edit 205
- Line Field, Create or Edit 207
- Outline Font, Download 209
- Page, Create or Edit 210
- Page, Delete 211
- Pitch Size, Set 211
- Point Size, Set 212
- Program Mode, Exit 213
- Syntax: tn 214
- Test and Service Commands 217
- Factory Defaults, Reset 218
- Formats, Print 218
- User-Defined Fonts, Print 221
- Full ASCII Table 223
- Character Sets 227
- International Character Sets 228
- Appendix B— Character Sets 230
- Extended Character Sets 231
- !"#$ 232
- Characters in Font 233
- Creating User-Defined Bitmap 235
- Graphics and Fonts 235
- delete character) 240
- User-Defined Interface 247
- Print Commands (t = 0) 248
- Shift Print Commands (t = 2) 250
- Protocol Commands (t = 4) 252
- Using Direct Graphics Mode 255
- What Is Run-Length Encoding? 256
- Direct Graphics Mode, Enter 258
- Change Origin 259
- End of Bitmap 259
- End of Line 259
- Raw Bitmap Data Follows 260
- Repeat Last Line 260
- Transition Black 260
- Transition White 260
- X19,Y450 261
- Hex Data Commands in Example 262
- , define command, 80, 167 264
- , define, 167 268
Produits connexes et manuels pour Imprimantes d'étiquettes UBI EasyCoder 201 II
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels