UBI EasyCoder 201 II Spécifications Page 147
- Page / 270
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7— IPL Command Reference
IPL Programmer’s Reference Manual 131
Pin 11/20 Protocol, Set (continued)
When a pin is set to flow control, the pin is high when there is room in the
data buffer. The pin is held low when the data buffer is full.
When a pin is set to ready/busy, the pin is high when the printer status is
ready. The pin is held low when the printer is in one of these conditions:
• Offline
• Buffer full
• No label stock
• Ribbon fault
• Label at strip pin
• Printhead hot
Postamble, Set
Purpose: Sets the postamble character.
Syntax: <EOT>n
where n specifies the postamble character.
Printers:
Printer Default Values for n Notes
All n = <NUL> Any ASCII character
When n = <NUL>, the printer
does not send a postamble
character.
All printers support this command
the same way.
Preamble, Set
Purpose: Sets the preamble character.
Syntax: <SOH>n
where n specifies the preamble character.
Printers:
Printer Default Values for n Notes
All n = <NUL> Any ASCII character
When n = <NUL>, the printer does
not send a postamble character.
All printers support this command
the same way.
- IPL (Intermec Printer 1
- Language) 1
- Programmer's 1
- Reference Manual 1
- Document Change Record 3
- Contents 10
- Before You Begin 13
- Safety Icons 14
- Global Services and Support 14
- Related Documents 15
- Introduction to IPL Commands 17
- What Is IPL? 18
- What Are IPL Commands? 18
- <STX>E2;F2<ETX> 20
- <STX> 20
- Example 1 23
- Example 2 23
- What to Read Next 24
- Downloading Fonts to the 25
- Printer 25
- Licensing Your Fonts 31
- Installing Code Page Tables 33
- Downloading Bitmap Fonts 34
- Downloading Outline Fonts 34
- Designing Bar Code Labels 37
- Introduction to Formats 38
- THIS IS THE SAMPLE LABEL 39
- Sample Label Command Strings 42
- Defining Label Design Fields 43
- Line and Box Fields 44
- Lines and Boxes Format 45
- Graphic Fields 46
- Editing Existing Fields 49
- Deleting Fields 50
- Positioning Fields 50
- Rotating Fields 51
- Scaling Fields 52
- Magnifying Bar Code Fields 53
- DUPLEX ANGLE CONNECTOR 54
- Graphic for Example 55
- Format for Example 55
- Data for Example 56
- Troubleshooting 59
- Troubleshooting Checklist 60
- Parameter Errors 61
- Image Overrun Errors 61
- Chapter 4— Troubleshooting 64
- Advanced Printer 65
- Programming 65
- Increasing Throughput 67
- Image Band Example 69
- Reimaging Modified Fields 71
- Using Emulation Mode 72
- Finding IPL Commands in This 79
- Commands Listed by Name 80
- Commands Listed by Syntax 84
- Commands Listed by Task 88
- Box Field Editing Commands 89
- Format Editing Commands 89
- Line Field Editing Commands 90
- Page Editing Commands 91
- Programming Commands 91
- UDC Field Editing Commands 91
- UDC Editing Commands 91
- Print Mode Commands 92
- IPL Command Reference 95
- Immediate Commands 102
- Status Dump 104
- Status Enquiry 105
- Print Commands 106
- Advanced Mode, Select 107
- Alphanumeric Field Separator 108
- Batch Count, Set 109
- Clear All Data 109
- Command Terminator 1 109
- Command Terminator 2 110
- Direct Graphics Mode, Select 112
- Emulation Mode, Enter 113
- Field, Select 113
- Field Decrement, Set 114
- Field Increment, Set 115
- Font, Transmit 116
- Form Feed 117
- Format, Select 117
- Format, Select (continued) 118
- Printers: 118
- Format, Transmit 119
- <ESC>N 120
- Memory Usage, Transmit 121
- Numeric Field Separator 122
- Options Selected, Transmit 123
- Page, Select 124
- Page, Transmit 124
- Program Mode, Enter 125
- Program Number, Transmit 126
- Quantity Count, Set 126
- Storage Area Usage, Transmit 127
- Test and Service Mode, Enter 127
- Warm Boot 128
- Configuration Commands 129
- Amount of Storage, Define 130
- Auto-Transmit 1, Enable 131
- Auto-Transmit 2, Enable 131
- Auto-Transmit 3, Enable 131
- Syntax: <SI>An 133
- Printers: 133
- Cutter, Enable or Disable 134
- Dark Adjust, Set 134
- Syntax: <SI>Cn 135
- Intercharacter Delay, Set 138
- Label Rest Point, Adjust 139
- Label Retract Distance, Set 140
- Label Stock Type, Select 141
- Label Width, Set 141
- Maximum Label Length, Set 142
- Media Sensitivity, Select 143
- Message Delay, Set 144
- Number of Image Bands, Set 145
- Pin 11/20 Protocol, Set 146
- Postamble, Set 147
- Preamble, Set 147
- Print Speed, Set 148
- Printer Language, Select 149
- Printhead Pressure, Set 152
- Ribbon Save Zones, Set 153
- Top of Form, Set 155
- Program Mode Commands 156
- Bar Code, Select Type 157
- Code 39 158
- Code 93 158
- Interleaved 2 of 5 159
- Code 2 of 5 159
- Codabar 159
- Code 11 160
- Code 128 160
- UPC/EAN 162
- HIBC Code 39 163
- Code 16K 163
- Code 49 164
- POSTNET 164
- Code One 167
- MaxiCode 170
- JIS-ITF 172
- HIBC Code 128 173
- QR Code 175
- MicroPDF417 176
- Syntax: yn 178
- Printers: 178
- Box Field, Create or Edit 182
- Syntax: rn 184
- Command Tables, Load 187
- Current Edit Session, Save 188
- Field, Delete 188
- Field Data, Define Source 189
- Field Direction, Define 191
- Field Origin, Define 191
- Font Character Width, Define 192
- Font Type, Select 194
- Format, Create or Edit 196
- Within a Page, Define 198
- Graphic, Select 200
- Graphic or UDC, Define 200
- Syntax: hn 201
- Interpretive Field, Edit 205
- Line Field, Create or Edit 207
- Outline Font, Download 209
- Page, Create or Edit 210
- Page, Delete 211
- Pitch Size, Set 211
- Point Size, Set 212
- Program Mode, Exit 213
- Syntax: tn 214
- Test and Service Commands 217
- Factory Defaults, Reset 218
- Formats, Print 218
- User-Defined Fonts, Print 221
- Full ASCII Table 223
- Character Sets 227
- International Character Sets 228
- Appendix B— Character Sets 230
- Extended Character Sets 231
- !"#$ 232
- Characters in Font 233
- Creating User-Defined Bitmap 235
- Graphics and Fonts 235
- delete character) 240
- User-Defined Interface 247
- Print Commands (t = 0) 248
- Shift Print Commands (t = 2) 250
- Protocol Commands (t = 4) 252
- Using Direct Graphics Mode 255
- What Is Run-Length Encoding? 256
- Direct Graphics Mode, Enter 258
- Change Origin 259
- End of Bitmap 259
- End of Line 259
- Raw Bitmap Data Follows 260
- Repeat Last Line 260
- Transition Black 260
- Transition White 260
- X19,Y450 261
- Hex Data Commands in Example 262
- , define command, 80, 167 264
- , define, 167 268
Produits connexes et manuels pour Imprimantes d'étiquettes UBI EasyCoder 201 II
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels